A600-027 Steam Press Stand,Black

Some folks complain that this stand is not tall. This is meant for sitting while ironing (for example when watching TV :) )

Love it. Stand could be a little higher but overall love it. Bought for my lab coats. A little book on techniques would be very helpful. That’s only suggestion I would make.

It is sturdy enough for my iron press!

I was very impressed when I opened the box containing this stand. It was much nicer and better quality than I was expecting. Until I saw it in person, I thought that it was overpriced, and I still think that the price is too high, but I was really expecting much lower quality based on the photo in the listing. When I read other reviews, I often wonder about people who struggle to assemble something, so now its your turn to wonder about me: In principle, attaching the top to the stand seems like it should be super easy, but I had a heck of a time getting the bolts that attach the top to the stand to cooperate with me. There was, perhaps, a bit of a warp in the table (although when I finally got it together, it looked great—it was fine). I made the mistake of installing the bolts on one end of the top completely (which seemed easy) before I moved to the other side. Then, when I tried to attach the bolts on the other side, those bolts would not draw down. Worse still, the nut slipped inside the small protrusion intended to hide it on the bottom of the table so that I couldn’t get hold of the nut to unscrew it so that I could try again. The little warp I referred to was especially problematic at that point, because the top of the table spread apart from the base at one end and drew the nut into the protrusion more. I probably didn’t have the right tools, really—a clamp to squish the pieces together so that the nut was exposed would have helped. In the end, I managed to squeeze the pieces together with one hand hard enough so that I could wrangle the nuts off with a pair of flat nosed pliers (no way of using a wrench to get the nut out of the protrusion) so that I could try again. I ended up taking all four bolts out, and reinstalled them all at the same time. I put each nut on and made sure that the bolt would draw down merely by screwing the bolt with my screwdriver. That was the key. (It seemed to me (in my ignorance, perhaps) that it mattered which way I put the nut on…but I had to attach them and experiment before I realized that the bolt would draw down without holding on to the nut, if I installed it correctly.) Once I had that figured out, I went around from bolt to bolt and merely screwed each one a little at a time until all four were firmly attached. It may be that I was a bit of a dunce about the whole business (I’m sure some of you are laughing), but hopefully my admissions will help you. :) I hope I’ve explained clearly enough to be helpful to someone. The stand is sturdy and looks great, but I think the whole process should have been easier.

Well I guess I didn't read the description well enough because this is designed to use while sitting down. Also mine came with no screws to mount the table to the base.

I've had this thing for years now and it still looks great. I use the iron on a daily basis so it stays set up. I do move it from room to room, it takes down very easily. It makes ironing much easier since I don't have to keep it in one spot or put it on a table. The stand is definitely a plus to have.

Great build quality but it's super short, you'd have to be 5ft tall or under to really use it. Not good for tall people. Tried to return this but still got shipped.🤬

This Steam Press stand is designed to be used while in a seated position. If you are under 5ft. tall this may be comfortable to use while standing. The level of sturdiness is reduced when operated from a standing position and can seemingly cause the stand to tip forward. It is much safer to use while seated, especially since you have more control of your hand placement, reducing the possibility of being burned.

it is secure when you place the steam iron on top of this stand got 3 problem 1- hight is too short,2- adjusting of hight is not easy and smooth,3-costly

No me gusto que la altura no es regulable

Had to return the produce the Iron that I purchased with the stand did not fit on the stand. too bad

Queda muy abajo la plancha