RØDE VXLR+ 3.5mm TRS to XLR Adaptor,Black

​I bought the VXLR+ because cheap, passive 3.5mm adaptors completely fail with this setup. I wanted to run a V-MODA BoomPro headset mic into my Focusrite Scarlett Solo, and this active adaptor solved the issue instantly. ​The audio signal is completely clean with excellent sound quality, allowing me to dial in the preamp gain with zero static or interference. The build quality feels rock-solid. I’ve now used it daily for several months without a single hitch, though keep in mind I leave it permanently plugged into the interface, so I haven't stressed the physical wear and tear of constant plugging. ​Verdict: A flawless solution for connecting a 3.5mm headset mic to an XLR preamp input. Skip the cheap alternatives and get the right adaptor first time.

If you want to connect your Rode lav mic or wireless mic to a making desk with phantom power you need this device. I tried to make a lead to block phantom power reaching the output of the wireless go receiver. It worked but did introduce some noise. This device is compact and effective. it comes with a plastic clip attached to you can plug an XLR cable into the adapter and clip it to your belt. This means that there is no weight put on the lav mic. If you are plugging this device indirect into a mixing desk then you need to remove the clip. On the packaging there is a circuit diagram of the device. It does not show that magic happens inside but for a technical person it provides enough information. The XLR output is mono unbalanced. so keep cable runs short or use a DI box to create a balanced out put for longer runs. The input uss a TRS (Tip Ring Sleeve) 3.5mm jack plug. Only the Tip and Sleeve are connected. This is fine for the rode wireless go (single transmitter version) as the output of the receiver is present on moth tip and ring. If you are using the Wireless go 2 (dual transmitter version) you will either need to set output to mixed and have both transmitters on the one output. If you want to have each transmitter to have its own output then you will need two VXLR+ adapters and a SC11 TRS Splitter Cable. The receiver would then have to be switched to dual output mode. The photo above show how you would connect a Rode wireless go 2 to a mixing desk using a SC11 TRS Splitter Cable and two VXLR+ adapters. *The receiver used in the photo above is a Rode wireless receiver. It is for illustrative purposes only.

Connected this to a Zoom F3 sound recorder and TRS microphone and bingo. Works.

Got this to let me plug my Smartlav into a mixer (trying out as a possible means to voice over). As soon as I switched on phantom power (to deliver plug-in power - something the VXLR+ is meant to address) I got hum on that channel (lo-cut made no difference) - experiment terminated as not workable. It works OK as a standard VXLR as long as phantom power is off as I've used it to feed from my Wireless Go receiver; however, if phantom power was then needed for anything, the hum comes in. For that application (using the WiGo as a wireless link for a roving mic) I can feed the WiGo into a TRS input via a 3.5mm to 1/4" adapter. So, OK as a plain VXLR but forget the "+" Maybe the newer VXLR Pro will be better... Update: I’ve since used it on another system and the phantom power caused no hum. So it’s a “suck it and see” - may be a mismatch with something on my mixer…

Wonderful adapter!!!!!!!! Wow! I use it to connect my 3.5mm 5v beyerdynamic MMX 330 pro headset to my XLR preamp/high end audio gear. Really sounds amazing with this method. Mic quality is so much better than PC audio mic input. Night and day. In fact I'd put a lot of bad headset mic quality down to bad PC implementation. If you have an Audio interface /outboard gear And a wired headset. This is the way to go!

Yep seems to work 100% as intended. Solid build quality. I used it to get some gaming headphones to work with my XLR audio interface. The headphones need to have a splitter to separate the audio from the mic. This item just enables you to connect the 3.5mm mic lead (of the headphones) to an XLR input (and the audio lead of the headphone just goes in the normal audio output). So far it has worked flawlessly.

Arrived quickly. Works. Does exactly what I needed it to do. The only slight negative is that it has a clip on that stopped the xlr from plugging into where it needed to plug in, but I just removed the clip and it went on.

Convers the 3.5mm export from Wireless Go to XLR (probably works for other 3.5mm, but not tried it). Nice addition, so we can record direct onto camera if needed, or an amp. Sound quality very good.

Wirkt robust und funktioniert einwandfrei. Damit kann man jedes Standard-Headset-Mikrofon und jedes Handy-Lavalier-Mikrofon (das mit einem entsprechenden Adapter auf Stereo-Klinke kommt) an ein Audio-Interface seiner Wahl anschließen. Dadurch kann man selbst mit einer Reihe sehr günstiger Mikrofone eine hohe Aufnahme-Qualität erreichen, die so am Mainboard-Anschluss nicht möglich wäre (diese Mainboard-Eingänge rauschen i.d.R. stark und verfälschen den Klang). Den Preis von rund 25€ finde ich somit recht fair.

I cannot express how thrilled I am with the Rode VXLR Plus XLR to 3.5mm Transforming Adapter. This little device has completely transformed my audio setup and made my recording process so much smoother. The build quality of this adapter is top-notch. It feels sturdy and durable, which gives me the confidence that it will last for a long time. When I received it, I noticed the absence of any annoying 60-cycle hum or hiss that I experienced with cheaper adapters. What surprised me the most was how transparent the audio quality remained. My microphone sounded just as pristine as when connected directly to the interface. The VXLR Plus provided the necessary voltage conversion for my unpowered mics and I didn't experience any issues with audio levels or distortion. It's an active adapter with internal circuitry that does its job superbly. Even though the price is slightly higher than some alternatives, I can confidently say that it's worth every penny. The peace of mind and reliable performance it offers are unmatched, making it a worthy investment. Overall, the Rode VXLR Plus XLR to 3.5mm Transforming Adapter has exceeded my expectations in every way. It has solved all my connectivity challenges and allowed me to use my favorite microphones with ease. If you want a reliable and high-quality solution for your audio needs, I highly recommend this fantastic adapter. Bravo, Rode!

BUY NICE OR BUY TWICE. In the audio/visual world whether 'prosumer' or commercial, there are items worth investing in Llast and dont date. This adaptor is one of them. As an Australian, I buy Australian + quality whenever I can and the RØDE VXLRVXLR+ Minijack doesnt disappoint. I was impressed by the solid, weightiness of this item which imparts a feeling of quality and the clip-accessory it ships with is practical and a nice touch. It works great with xlr audio recorders (mine a Zoom H8) where you can lower the power output/gain with lavalier mics which are the most portable and cost-effective option for multi-person podcasting and travel setup. I bought two of these so far and will probably buy another few in early 2021. Great bang for buck. 5-star.

Used for Zoom M4 recorder, to adapt lavalier mics at XLR connection with phantom voltage. All OK, no problem.

Xlr giriş olan kamerana 3.5mm mikrofon bağlamak için aldım. Başarılı