Orange Rubber Stamp Sheet for Laser Engraving Machine with A4 Size 2.3mm (Orange)

This is a really neat product! I've made four custom stamps using this in my K40 laser and it's great! Engraves really well, and without too much odor. I'm super surprised how fine of detail can be engraved and stamped, much better than I expected. The fine white powder created during engraving is quickly and easily vacuumed up, and I usually wash the stamp in the sink after it's done. I tried cutting it with the laser once but it didn't work so well, so I just cut it with an x-acto knife after engraving. It would probably cut fine if I just took a couple passes at lower power, maybe I'll experiment more in the future. It took a while for the stamp pad I ordered to arrive, and I found that the stamps can also be inked using a permanent marker, it's just a little tedious.

I bought this to use with my Glowforge Pro and it's perfect! It's heavy enough to use without the need to use honeycomb pins of magnets to hold it down and doesn't move at all even with the added inline fan that I run. So happy with the stamp sheets, will definitely buy more when I run out.

I've been etching wood for about three years with my laser cutter, but this is the first time I've tried to etch rubber. So take my review for what it's worth. First, the rubber seems very durable right out of the package. I didn't try very hard, but I don't think you could crease it or tear it very easily by accident. For the etching, I made the Harriet Tubman stamp pictured. I went lighter on the laser settings that I do for wood because I didn't know what to expect. The first pass created a very light, ghost-like image. I then went to the same settings I use for wood, and I didn't get much more. I then went to 1.5 times what I use for wood, and I got the stamp you see pictured. For cutting, I went 1.5 times what I use for wood on a single pass, and I had to go around twice. Then I cleaned up the residue which I took a picture of. That's from one stamp measuring 1.8" square. The stamp itself turned out pretty good, I think, given that it's a face. I did it on wood first, and the results are identical. I haven't tried it yet, but I think I could get away with very clear 12 or even 10 point font. Overall, I think this is pretty good stuff. Just be prepared to clean out your laser cutter with each use.

Bought this rubber sheet to laser cut stamps and it works really well. I figured out that it works best with several passes of lower intensity rastering to prevent the rubber from burning, and I ended up cutting my stamps out of the sheet with a knife. There wasn't too much odor from this sheet (my cutter is closed with a vent, though), and the definition I got from the stamp was great. I'm subtracting one star because it was super difficult to clean. The best cleaner for me was a Windex-like product with a toothbrush.

this was just what i was looking for, made a stamp for my parents shop and it turned out perfect, it took a few passes to figure out the right settings for my laser engraver but i'm very pleased with the outcome, also very low odor when engraving

I was disappointed at first because I was having a hard time cleaning sticky residue off of the stamps. I later adjusted my settings on my laser and there is VERY little cleaning needed now, and it's ash instead of the sticky goo I was getting. For reference, I have a Thunder 80w CO2 laser. My settings are 180in/sec at 50% power. I cut at 10in/sec at 60% power, but that's probably overkill for the cutting. Very little air flow. I use a wide nozzle with the air just coming out enough to keep the lens clean.

This stuff works amazingly well when you: A. Have the laser focused correctly (much more important than with other materials it seems) B. Don't run the laser at too high of power (I used 25% power, 17% speed with 4 passes on a 60W ULS laser for engraving) C. Also be prepared to finish cutting out your stamp by hand with a super sharp craft knife (or scalpel)

This stuff is super cool! It was super easy to use and cleans up really easy with some tap water and a tooth brush! Now I cant stop making stamps!

It's perfect with the project we did.

Super service, very nice product