Bingfu Dual Band WiFi 2.4GHz 5GHz 5.8GHz 6dBi RP-SMA Male Antenna 15cm 6 inch Pigtail Cable 2-Pack for WiFi Router Wireless Mini PCI Express PCIE Network Card Adapter

The antennas and cables work as advertised and boosted my WiFi signal significantly on the 5 GHz band. My FiOS Gateway Router lacked external antennas. So, I opened it and installed one of these antennas using the included cable. This router has separate internal attachments for the 3 internal 5 GHz antennas, but I only installed one external antenna. The tiny plug fit perfectly on the connector on the circuit board - snapped right into place. The 2.4 GHz band is hardwired, but my issue was with the 5 GHZ signals. This instantly improved the signal strength on the 5GHz band at 25 feet from the router by 6 dBm. The signal went from a -65 dBm to -59 dBm. In other words from a poor to a good signal. If you plan to do this type of upgrade be very careful. I used the second antenna to upgrade one of the antennas on an older Linksys router I use as an access point. A signal improvement was obtained on both WiFi bands but not as significant since the stock Linksys antennas were fairly good. This is a very good good product for the price. Recommended.

They work. The price is right. Well made. I'm happy.

I used this to connect the factory installed Sirius XM antenna in a 2013 Ford F150 to my aftermarket Sirius SXV 300 tuner. Then plugged the SXV300 into my new Pioneer radio. Easy, clean install of the Sirius tuner without the hassle of running another antenna through the dash. The factory Sirius antenna plugged right into this cable, the other end connected to the antenna input on the SXV300 tuner. Perfect, secure fit.

Pretty decent antennas. I'm using these on a couple cyberdeck projects and they have been working out great and have extended my range and connectivity capabilities pretty well. Roughly 6 inches long, and a little thicker than others make these feel pretty sturdy.

Fairly durable I suppose for the price. They work well for me. I used them to increase the range of my Futaba transmitter. One of the solder joints broke (probably cuz I bent it) so it took me a looong time to re-solder it back together again inside the brass nut. Not fun. They do the job that's why I did 4 stars.

Used those antennas for upgrade my remote controller Fly Sky. Works great.

I loved them when I was planning out the project, which is to add external antennae to a router which has none with the expectation that it will improve performance. Everything was great until I attempted to put the router where I wanted it with the antenna mocked up, and it was unable to fit in the space. There's a shorter version, so I sent these back and will order the other to finish the project.

I installed this wireless antenna on a couple of Wyze cameras located far from the router and would intermittently drop the video feed. After install, the signal went from one bar to three bars. Installation did require taking apart the camera so doing this requires some DIY skill

Quality product. Works with ESP32 modules with anthena connectors.

Received this (part code X002MCD1RT) kit with the 2 wire connectors and 2 antennas. The problem is that the M2 connector side is 1) very small and 2) would not click into the Intel Wifi car'ds connector. I looked at it under a microscope and noted the centre female connector was bent/damaged. Rather than sending it back; I took a thumb tack and "pressed" in the centre (wiggling action so that it made the centre area/pin hole a bit bigger/recreated it). Then when I went to connect it ; it "clicked properly". Make sure it clicks, otherwise it may disconnect / be loose. This was made possible by previous reviewers that said it could click except for the 1 negative review. where it couldn't make a solid connection. ALso, I secured the antenna ends to some holes in the sheet metal of my case so I didn't need a PCI metal adapter/mount. Hope this helps the next person.

Antenna leads were sufficiently long to attach to the motherboard-mounted WiFi M2 card. Already had the holes in the case panel to attache the external antennae mounts. All took about 10 minutes to install and mount. The most challenging part had been attaching the leads to the WiFi card due to micro-sized connectors.

First time I ordered I didn't get the wires. Next time I ordered I got the wires but they are a horrible fit. It's not the first time I have attached wires to same cards. These wires do not snap in place. I did manage to get one wire mounted with the help of a small bracket I had kicking around so I'm not sending it back. Not impressed. Next would but the set with wires already attached.

One of the connectors is missing, so it is not suitable for those who do not have a soldering iron.